To Design and Fabricate Permanent Mould for Automative Components

To Design and Fabricate Permanent Mould for Automative Components

Bibliographic Details
Main Author:	LEE Tai Yean
Format:	Thesis Book
Published:	Serdang : Universiti Tenaga Nasional , 2007
Subjects:	Universiti Tenaga Nasional > Dissertation

Similar Items

Coe In-Building Coverage Design at GSM 1800 mhz
by: ERIC Chai Ko Yee
Published: (2007)

Design of Reed Solomon Encoder/Decoder using VHDL
by: YONG Wei Pin
Published: (2007)

Development of Flowcharts for Wireless Sensor Network and Recommadation Interface for Future Design
by: CHOW Jun Yan
Published: (2007)

Analysis and Design of A High Rise RC Building for Siesmic Load
by: MOHD Ali Amin Ab. Latif
Published: (2007)

Optimization of underground car park beam design to improve available safe egress time (aset) using numerical method[Thesis]
by: Ahmad Faiz Bin Tharima @ Zainuddin

Design and fabrication of a composite rocket
by: Michael Sen
Published: (2005)

Wind Tunnel Testing of the Loft Angle Effect on Golf Driver Head
by: BADRUL Qamar Sulong
Published: (2007)

Remote Baby Monitor with Selective Voice Activated Feature
by: AHMAD Nasri Zakaria
Published: (2007)

The Effect of Automatic Voltage Regulator on Transient Stability of Power System
by: MUHAMAD Farid Nasir
Published: (2007)

Study of Residental Power Frequency Magnetic Fields in Alor Setar, Kedah, Malaysia
by: NG Cheng Lim
Published: (2007)

Study on Energy Harvest and Utilization of Domestic Sewage and Waste
by: LOH Sing Yee
Published: (2007)

Method of Expediting The Aging Process of Rice
by: TING Yik Hwa
Published: (2007)

Database of Stress Intensity Factor for Part-Through Cracks
by: ROZAIL Fitri Othman
Published: (2007)

Development of A 2D Unstructed Triangular Mesh Generator
by: KANG Chuu Liu
Published: (2007)

A Study on The Control Techniques Employed in Distributed Generation
by: AARON Devadas Mosses
Published: (2007)

Lusas Simulation on The Performance of Steel Lattice powerline Structure : Case Study TNB Suspension Tower Type
by: MOHD Nor Hamim Samsun Baharun
Published: (2007)

A General Purpose Processor (GPP) Based Switching and Routing Prototype
by: LAU Chin Wei
Published: (2007)

Development of YTTRIA : Stabilized Zircunia Doped with Nano Neodymium Oxide Powders for Orthopedic Applications
by: TEY Kuan Chung
Published: (2007)

A Computer Modelling of Wrapper Redundancy Logic for MBISR
by: WONG Weng Yew
Published: (2007)

Simulation A Six Degree of Freedom Articulated CRS Robot Using Matlab/Simulink and Virtual Reality
by: MOHD Fazreen Mohd Fauzi
Published: (2007)

GSM Software for Hybrid Location Tracker
by: BONG Kai-Yi
Published: (2007)

Balancing Robot
by: YEOH Wei Zheng
Published: (2006)

Knowledge management implementation framework : A case study in a research institute [Thesis]
by: Saidatina Asmah binti Ajuhary
Published: (2016)

Empowering employees through bring your own device: The benefits and challenges in Malaysian public sector[Thesis]
by: NorHazilah Binti Mahat

Critical success factors for information technology (it) project management in public sector[Thesis]
by: Mohamad Sha Bin Dawang

Multi-area economic dispatch problems using differential evolution immunized ant colony optimzation (deiant) technique considering generation cost and power loss[Thesis]
by: Nurul Hidayah Binti Marzuki

Solar pv placement and sizing for line stability enhancement and optimal operating cost[Thesis]
by: Jayidah Binti Mat Salleh

Happiness at work : determinants of employee wellbeing among government servants in Putrajaya[Thesis]
by: Bibi Aida Binti Ab Rasid

Critical success factors of it/is outsourcing in Malaysian Public Sector[Thesis]
by: Noura Binti Mohamad Ghazali

A Study on Perceptions of Organizational Culture, Job Design, Job Constraints, and Motivational Factor Towards Job Satisfaction Among Enforcement Officers (PLCDUINO) [Thesis]
by: Mohd Khairi bin Jamaludin

Ann technique to estimate leakage current level over the transdormer bushings
by: POR, Choon Yim
Published: (2005)

Predictive modeling for dengue patient's hospital lenght of stay using predictive analytics[Thesis]
by: Henni Jumita binti Muhamad Hendri
Published: (2017)

Critical factors in successful implementation of knowledge management using cloud computing by public sector in Malaysia[Thesis]
by: Nabilah bt Mahmud
Published: (2017)

Development of a lab-scale detection system to capture voltage variation under simulated cloud charge prior to lightning[Thesis]
by: Lilywati binti Manap
Published: (2017)

A change management model : Transformation towards 1 Goverment Enterprise Architecture[Thesis]
by: Ruhana binti Abd Rahman
Published: (2017)

A knowledge management strategy framework to improve knowledge management readiness in organisations : A case study in a government organisation [Thesis]
by: Norliza binti Jumeri
Published: (2011)

Process Parameters for Quantum Dot Lateral P-I-N Photodiode using Taguchi`s Optimization Method [Thesis]
by: Siti Kalthom binti Tasirin
Published: (2013)

Stastiscal study of ionsphere critical frequency during solar minimum
by: Mohd SHAHARUDDIN bin Mohd
Published: (2006)

Development of power flow program using matlab
by: CHONG sue Joung
Published: (2006)

Acquiring modal properties of built in beam using fini te element analysis
by: MOHAMMAD Shariman b. Mohammad Lukhman
Published: (2006)