Characterization and parametric evaluation of wire eletrical discharge machining of cold work tool steels[Thesis]

Characterization and parametric evaluation of wire eletrical discharge machining of cold work tool steels[Thesis]

Bibliographic Details
Main Author:	Mohd Aidil Shah Bin Abdul Rahim
Format:	Thesis Book
Subjects:	Universiti Teknikal Malaysia > Dissertations

Similar Items

Study of optimal machining parameters when machining AISI 304 stainless steel with carbide-PVD coated (TiAIN) cutting tool [Thesis]
by: Mohd Yusri Bin Mohd Rahim
Published: (2013)

Evaluation on machining performance of AISI 1045 steel under dry condition [Thesis]
by: Mohd Khairul Nizam bin Ab Ghani

Micro-Fabrication using Micro-Wire electrical discharg machining
by: AISY Anuarin b Abdullah
Published: (2008)

Characterization and Optimization of N-Channel Trench Power Mosfet [Thesis]
by: Maslinda binti Hadinan

Characterization and optimization of 32nm p-channel MOSFET device [Thesis]
by: Nasaruddin bin Mohammad @ Khalid
Published: (2013)

The effect of drilling parameters on central wear, flank wear and surface roughness for drilling of stainless steel 304 [Thesis]
by: Zambri Bin Abd Halim
Published: (2013)

Study on machining assob 718HH with electrical discharge machining (EDM) using taghudi method
by: MOHAMMAD Azhar Bin Harshah
Published: (2008)

Ultimate strength of cold-formed steel z-purlins : Mohamed Ali Abdul Razak
by: MOHAMED Ali Abdul Razak
Published: (1980)

An economical roof design using cold formed steel section[Thesis]
by: Patrick Basun @ Patrick Woon
Published: (2014)

CNC machining with automatic tool management
by: MOHD Hafiz b. Mohd Nawawi
Published: (2008)

Analysis of arch bridge-parametric study
by: ATIKAH Zakaria@Ya
Published: (2005)

Category 6 UTP cable health check for performance evaluation at ILP Selandar [Thesis]
by: Asbul Hadi bin Mat Yunus
Published: (2012)

Effect awareness of industry revolution 4.0 on small medium practitioners activities towards investment of technology[Thesis]
by: Noorharnani Binti Mohd Sarkawi

Study and Analyze The Optimum Parameters of Wirecut-EDM (Sodick VZ 500L) For SKD11 Tool Steel Machining [Thesis]
by: Amer Isyraqi bin Hussin

Wired USA
Published: (2025)

Wired USA
Published: (2025)

study on the selection of cutting tool for machining turned component
by: MAHADZIR b. Hj. Ahmad
Published: (1991)

A Non-parametric approach : Malaysian commercial Banks efficiency foreign vs domestic
by: SYARIFAH Adlina Syed Abdullah
Published: (2005)

Influence of Nonlinear Servo Motor in Single Pulse Simulation of Electrical Discharge Machining System Modelling [Thesis]
by: Hassan bin Lee

Analysis of communication ability for cooperative mobile robots [Thesis]
by: Ahmad Fauzi Shah bin Mohd Arifin
Published: (2014)

rHDPE/rPP hybrid blends from injection molding scrap : Characterization for conventional milling workpiece application [Thesis]
by: Siti Zaleha binti Wahid

Electronic compass using hall-effect sensor
by: SITI Nor Baeyah binti Mohd Nasir
Published: (2005)

Impak Pelaksanaan Amalan Persekitaran Berkualiti 5S di Institut Teknikal Jepun Malaysia [Thesis] : Mohd Raris bin Mohamed Yusof
by: Mohd Raris bin Mohamed Yusof
Published: (2013)

Research on ability of partial discharge detector
by: AZHAR bin Abdullah
Published: (1993)

Penentuan partial discharge didalam penebat
by: MAT Nasir bin Kari
Published: (1983)

Process Capability Analysis for Wire Bonding
by: SUHAIDI Latip
Published: (2006)

Double head if wire rope sensor
by: NUR Hazirah bt Zaini
Published: (2008)

No more cold calling : the breakthrough system that will leave your competition in the dust
by: BLACK
Published: (2006)

Evaluation of surgical treatment of displaced paediatric radius and shaft fractures by percutaneous cross K-wiring
by: CHANG Kok Chun
Published: (2004)

Pavement rehabilition using cold in place
by: ABD Hakim bin Mohd Najili
Published: (2006)

Mr. Icy-Cold and other stories
by: BLYTON
Published: (2001)

Evaluation of magnetic properties on electrical steels using H-coil sensor
by: NADIAH bt Halim Khoo
Published: (2008)

Dvelopment of a sustainable material selection for bumper fascia using analytical hierarchy process (AHP) [Thesis]
by: Zamzury Bin Mat
Published: (2013)

Productivity improvement for assembly line using lean manufacturing approach [Thesis]
by: Irwan Affandi Bin Abdul Rahman
Published: (2013)

Design and simulation of proposed automation sytem in existing manufacturing enviroment [Thesis]
by: Zainila Binti Salam
Published: (2013)

Simulation and analysis of material transport system in automative industry[Thesis]
by: Azizi Bin Bahari
Published: (2013)

Development of raw materials storage management system for Japan- Malaysia Technical Institute[Thesis]
by: Hishammudin Bin Ahmad
Published: (2013)

Automated pallets tracking system for manufacturing assembly area[Thesis]
by: Zamzuri Bin Hassan
Published: (2013)

The effect of cooling rate on mechanical and morphological properties of heat treated recycled aluminum alloy from scrap [Thesis]
by: Haji Azim B. Aziz
Published: (2013)

Ergonomic risk factors assessment in material handling at warehouse operations [Thesis]
by: Rosmiza Binti Majid
Published: (2013)